My sister, Stephanie, agreed to tackle the job with me and today when our new Sleep Number bed came we finally got the finished look. I can't be more thrilled with how it turned out.
As I said, when I laid out the plans for our new gray and white master bedroom, I was inspired by a dropcloth headboard I'd come across on pinterest originally done by Tenth Avenue South.
|Pottery Barn Camelback Raleigh Headboard|
|DIY Dropcloth Headboard by Tenth Avenue South|
The only supplies we needed were:
1" foam (I used two packs of NU-Foam Baby Bumper Pads)
9x12 or 12x15 Canvas Drop cloth
Upholstery Nails or Nail head trim kit
Hammer or tack hammer
Here's how we did it:
My sister and her husband went to the hardware store to pick up the plywood for me using the dimensions I had drawn. Home Depot and Lowes will both cut it for you to size -- but only straight lines. Unfortunately, they didn't have plywood quite tall enough (59" was the required height) so we had to get two pieces. We were easily able to nail them together using a third piece along the back to connect them.
I had cut out the curve of the top of headboard on a piece of cardboard. We traced it directly on the plywood, then flipped the cardboard and did the same thing on the other half to make sure the curve was the same on both sides.
We then used the jigsaw to cut the curve. Slow and steady is the key. I was a little nervous because the cut wasn't exactly on the line, but after putting the foam and batting down it hides a lot of the mistakes.
After the curve was cut out, we worked on the legs. To be honest with you, we decided later there was no real reason to have legs. It just creates extra work to attach and/or cut them out of the plywood depending on how you do it. If you keep the bottom of the headboard straight all the way across, it actually gives it more support. Plus, you can't see the legs now that the bed is pushed up against it. This is one of the only things I would have done differently.
Next, we laid the plywood headboard flat and used spray adhesive to attach the foam. We laid it straight across, covering the entire curve and then later cut the foam down to shape using scissors.
|Attaching the 1" foam pieces|
|Here's how it looked from the back after putting on the foam, but before cutting the foam to shape|
I had a lot of trouble finding enough 1" foam to cover this beast. I did find two bags of foam meant for crib bumpers. Each came with six pieces and each piece was 1"x10"x26" in size. At that size I needed about 4 bags to completely cover the plywood. I actually ended up having a lot of trouble finding any more than two bags and we were up against the clock, so we went to plan B.
The original plan was to put foam all over the headboard and then put two layers of batting all over headboard and staple gun it around the back. But since we were short on foam, we had to improvise. I decided I would put on as much foam as I had and then I would fold over the batting to be double thick in the bottom area where I did not have any foam. I only put a single layer of batting over the foam area. Thanks to my brother in law's extensive power tool collection we were able to put the batting on in a matter of minutes using an air compressor and staple gun. A regular staple gun would have worked fine, just make sure to put a lot of pressure on it.
|Batting on - front view|
|Batting on back view|
cloth. I bought a 9' by 12' canvas drop cloth found in the paint aisle at Home Depot. I washed, dried and ironed it before we laid it out to cover headboard. The drop cloth had a huge seam running through the middle which I was nervous about. However, even the king size headboard only required half of the drop cloth so the seam didn't end up being an issue at all. I actually cut the drop cloth in half right at the seam and plan to use the other half to make a matching upholstered bench for the end of the bed.
With the drop cloth laid out on the floor and the headboard centered on top, I pulled it tight as Stephanie used the staple gun to attach it. We started at the top middle and worked our way around each size, pulling it taunt as we went. Around the legs I folded the material neatly -- this is where the air compressor really came in handy -- because going through a few layers of fabric, batting and wood was a little tough.
The final step was putting on the nail head. The Pottery Barn headboard and the DIY one that inspired by both put the nail head trim on the edge of the headboard. I decided I would rather
|Headboard inspiration with nails on side/top|
It's hard to tell from the photos but the upholstery nails I used are pretty big -- unlike the upholstery nail head kits you can buy which are much smaller and less expensive. The exact nails I used can be found here.
While this was the most expensive and frustrating part of the process for me -- it was also the most rewarding. I put the first nail head in and then kind of eyeballed where I wanted the second to go. Then I used that distance, which was about 1.25", for the rest of them. I had about two dozen duds, where the point of the nail would actually bend or break -- but otherwise it was just a matter or getting the nail to go into the wood and stay there. This is where I'm glad we only did one layer of batting over the foam, because otherwise it may have been too thick for the nails to go through all of that material.
-- as he wondered aloud why they were shipped separately. When I told him I made it, his mouth dropped and he barely believed me until I showed him the leftover drop cloth. And I quote he said: "You just saved like $1500 -- I bet your husband is thrilled, girl. It looks exactly like ours."
I love our new drop cloth upholstered headboard and I am so happy we decided to take on this DIY challenge because the finished product is just what I was looking for at a fraction of the price! For those wondering, yes, I made the throw pillows to match the comforter. Here's the tutorial for how to make throw pillows in five minutes. No, seriously!
Here's how the cost of the DIY upholstered broke down:
Plywood: $48 (enough left over to make a bench)
Drop Cloth: $28 (enough left over to make a bench or another headboard)
2 Bags of 1" Foam: $25 (I used 50% off coupons for each)
Batting: $3 (Originally $25, but I was able to use a $10 off coupon combined with a 50% off coupon)
Adhesive Spray: $5
Nail Heads: $55 (enough left over to make bench)
A few more pictures....